Transmission Manuals – All data about Transmission

P0781  1-2 Shift (1-2 Shift Valve)  

Description
The 1-2 shift valve performs shifting to 1st gear and other gears. when shifting to 2nd and 4th gears is impossible, of when the ECM directs the transmission to switch 5th or 6th gear and the engien overruns (clutch slips), this DTC is output.

DTC CodeDTC Detection ConditionTrouble Area
P0781When conditions (a) and (b), or (a) and (c) are met. (2-trip detection logic)
(a) When the ECM directs the transmission to switch to 2nd gear, the actual gear is shifted to 1st.
(b) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 3rd.
(c) When the ECM directs the transmission to switch to 5th gear, the engine overruns (clutch slips).
·Valve body is blocked up or stuck (1-2 shift valve)·Shift solenoid valve SLT remains open or closed·Automatic transmission (clutch, brake or gear, etc.)

Monitor Strategy

Related DTCsP0781: Valve body/Functional check
Required sensors/ComponentsValve body, Automatic transmission assembly
Frequency of operationContinuous
DurationCondition (A) and (B)
0.4 seconds
Condition (C)
3 seconds
Condition (D)
1 second
MIL operation2 driving cycles
Sequence of operationNone

Typical Enabling conditions

The monitor will run whenever the following DTCs are not presentP0717 (Turbine speed sensor circuit)
P0722 (Output speed sensor circuit)
P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit)
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0979, P0980 (Shift solenoid valve S3 circuit)
P0982, P0983 (Shift solenoid valve S4 circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit)
P0327, P0328, P032C, P032D (KCS sensor circuit)
ETCS (Electric Throttle Control System)Not system down
Transmission position“D”
Duration time from shifting “N” to “D”4 seconds or more
ECT40°C (104°F) or higher
Spark advance from max. retard timing by KCS control0° crankshaft angle or more
EngineStarting
ECM selected gear2nd
Vehicle speed2 km/h (1.2 mph) or more
Output speed2nd → 1st down-shift point or more
Throttle valve opening angle9% or more at 2000 rpm
(Conditions vary with engine speed)
Calculated load value7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.11 to 7.58
or
1.83 to 2.27
or
1.24 to 1.49
or
0.93 to 1.07
or
0.66 to 0.80
or
0.51 to 0.65
ECM selected gear4th
Vehicle speed2 km/h (1.2 mph) or more
Throttle valve opening angle9% or more at 2000 rpm
(Conditions vary with engine speed)
Calculated load value7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.11 to 7.58
or
1.83 to 2.27
or
1.24 to 1.49
or
0.93 to 1.07
or
0.66 to 0.80
or
0.51 to 0.65
Current ECM selected gear5th
Last ECM selected gear4th
Vehicle speed (During transition from 4th to 5th gear)Less than 100 km/h (62.2 mph)
ECM selected gear5th
Engine speed -Turbine speed (NE – NT) (After transition to 5th gear)150 rpm or less
Vehicle speed (After transition to 5th gear)Less than 100 km/h (62.2 mph)

Procedure
1. Check DTC output (In addition to DTC P0781)
a. Connect the Diagnostic scanners.
b. Read the DTCs.

ResultProceed to
Only P0781 is outputA
P0781 and other DTCs are outputB

A>> Perform active test.
B>> Go to DTC chart.

2. Perform active test (running test)
Caution: This test should always be performed with at least 2 people.
a. Connect the diagnostic scanners.
b. Clear the DTC.
c. Warm up the engine.
d. According to the display on the diagnostic scanners, perform the active test.

Tester DisplayTest PartControl RangeDiagnostic Note
Control the Shift PositionOperate shift solenoid valve and set each shift position·Press “→” button: Shift up·Press “←” button: Shift downPossible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less

Ok>> Perform active test (shift solenoid valve SLT)
NG>> Repair or replace transmission valve body assembly.

3. Perform active test using Diagnostic scanners (Shift solenoid valve SLT)

a. Remove the test plug on the transmission case center right side and connect SST.

b. Connect the diagnostic scanners.

c. Start the engine and warm it up.

d. Measure the line pressure with SST.

e. According to the display on the diagnostic scanners, perform the active test.

f. Measure the line pressure.

Tester DisplayTest PartControl RangeDiagnostic Note
Activate the Solenoid (SLT)*Operate shift solenoid SLT and raise line pressureON or OFF
HINT:·OFF: Line pressure up (when Active Test “Activate the Solenoid (SLT)” is performed, ECM commands SLT solenoid to turn OFF)·ON: No action (normal operation)
[Vehicle Condition]
·Vehicle stopped·Engine idling

OK>> Cleasr DTC and perform running test.
NG>> Replace shift solenoid valve SLT.

4. Clear DTC and perform running test.
a. Clear DTC.
b. Check for DTC again after conducting the monitor drive pattern.
OK>> No DTC output.

Ok>> END.
NG>> Repair or replace automatic transmission assembly.