Transmission Manuals – All data about Transmission

 P0748  Pressure Control Solenoid “A” Electrical (Shift Solenoid Valve SL1) 

Description:
Shifting from 1st to 5th is performed is combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled the ECM. If an open or short circuit occurs in the shift solenoid valves, the ECM controls the remianing normal shift solenoid valves to allow the vehicle to be operation safely.

DTC CodeDTC Detection ConditionTrouble Area
P0748The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gear (1 trip detection logic)
Output signal duty equals to 100%
HINT:SL1 output signal duty is less than 100% under normal condition
·Open or short in shift solenoid valve SL1 circuit·Shift solenoid valve SL1·ECM

Monitor Strategy:

Related DTCsP0748: Shift solenoid valve SL1/Range check
Required sensors/ComponentsShift solenoid valve SL1
Frequency of operationContinuous
Duration1 second
MIL operationImmediately
Sequence of operationNone

Typical Enabling Conditions:

The monitor will run whenever the following DTCs are not presentNone
Ignition switchON
StarterOFF
Solenoid current cut statusNot cut
Battery voltage11 V or more

Wiring diagram:

Hint:
the shift solenoid valve SL1 turns ON/OFF normally when the shift lever is on D:

ECM gear shift command1st2nd3rd4th5th6th
Shift solenoid valve SL1OFFOFFOFFOFFONON

Procedure:
1. Inspect No. 1 transmission wire (shift solenoid valve SL1)

a. Disconnect the D63 No. 1 transmisson wire connector.

b. Measure the resistance according to the value(s) in the table blow:

Tester ConnectionConditionSpecified Condition
11 (SL1+) – 3 (SL1-)20°C (68°F)5.0 to 5.6 Ω
11 (SL1+) – Body groundAlways10 kΩ or higher
3 (SL1-) – Body groundAlways10 kΩ or higher

OK>> Check harness and connector (No. 1 transmission wire ECM)
NG>> Inspect shift solenoid valve SL1.

2. Check harness and connector (No.1 transmission wire – ECM).

a. Disconnect the D74 ECM connector.

b. Measure the resistance according to the value(s) in the table below.

Tester ConnectionConditionSpecified Condition
D74-14 (SL1+) – D74-15 (SL1-)20°C (68°F)5.0 to 5.6 Ω
D74-14 (SL1+) – Body groundAlways10 kΩ or higher
D74-15 (SL1-) – Body groundAlways10 kΩ or higher
ResultProceed to
NGA
OKB

A>> Repair or replace harness or connector.
B>> Replace ECM.

3. Inspect shift solenoid valve SL1.

a. Remove shift solenoid valve SL1.

b. Measure the reisistance according to the valvue(s) in the table below.

Tester ConnectionConditionSpecified Condition
1 – 220°C (68°F)5.0 to 5.6 Ω

c. Connect the battery’s positive (+) lead with a 21 W bulb to terminal 1 and the negative (2) lead to terminal 2 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
OK: Valve moves and makes an operating noise.

OK>> Repair or replace No. 1 transmission wire.
NG>> Replace shift solenoid valve SL1.