P0729 Gear 6 Incorrect Ratio
Description:
The ECM uses signals from the output speed sensor SP2 and input speed sensor NT to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear). Then the ECM compares the actual gear with the shift shedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve bodt or automatic transmissin (clutch, brake, gear, etc.).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0729 | 6th gearshift malfunction:The ECM determines there is a malfunction when both of the following conditions are met. (2-trip detection logic) (a) When the ECM directs the transmission to switch to 5th gear, the actual gear is also shifted to 5th. (b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th. | ·Valve body is blocked up or stuck (sequence valve)·Shift solenoid valve SLT remains open or closed·Automatic transmission (clutch, brake or gear, etc.) |
Typical enabling conditions:
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0979, P0980 (Shift solenoid valve S3 circuit) P0982, P0983 (Shift solenoid valve S4 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit) P0327, P0328, P032C, P032D (KCS sensor circuit) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | “D” |
| Duration time from shifting “N” to “D” | 4 seconds or more |
| ECT | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| Calculated load value | 7.75% or more (A/C off) 7.75% or more (A/C on) |
| Input speed/output speed (NT/NO) NT: Input (Turbine) speed NO: Internal counter shaft speed | 3.11 to 7.58 or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
Procedure:
1. Check DTC output (in addition to DTC P0729)
| Result | Proceed to |
|---|---|
| Only P0729 is output | A |
| P0729 and other DTCs are output | B |
2. Perform active test (running test).
This test should alwys be performed with at least 2 people.
– Perform the test at the normal operating ATF temprature: 50 to 80 degree C (122 to 176 degree F).
Perform the test with the A/C turned off.
Engine and ECT:
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operate shift solenoid valve and set each shift position | ·Press “→” button: Shift up·Press “←” button: Shift down | Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (30 mph) or less |
3. Perform active test (shift solenoid valve SLT).
– Perform the test at the normal operating ATF temperature: 50 to 80 degree C (122 to 176 degree F).
– Be cafeful to prevent SST’s hose from interfering with the exhaust pipe.
– Perform the test with the A/C off.
a. Remove the test plug on the transmission case center right side and connect SST.
b. Connect the diagnostic scanner.
c. Start the engine and warm it up.
d. Measure the line pressure with SST.
e. Turn on the diagnostic scanner.
f. According to the display on the diagnostic, perform the active test.
g. Measure the line pressure.

Engine and ECT:
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Solenoid (SLT)* | Operate shift solenoid SLT and raise line pressure | ON or OFF HINT:·OFF: Line pressure up (when Active Test “Activate the Solenoid (SLT)” is performed, ECM commands SLT solenoid to turn OFF)·ON: No action (normal operation) | [Vehicle Condition] ·Vehicle stopped·Engine idling |
Ok>> Clear DTC and perform running test.
NG>> Replace shift solenoid valve SLT.
5. Clear DTC and perform running test.
OK>> end.
NG>> Repair or replace automatic transmission assembly.