P0781 1-2 Shift (1-2 Shift Valve)
Description
The 1-2 shift valve performs shifting to 1st gear and other gears. when shifting to 2nd and 4th gears is impossible, of when the ECM directs the transmission to switch 5th or 6th gear and the engien overruns (clutch slips), this DTC is output.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0781 | When conditions (a) and (b), or (a) and (c) are met. (2-trip detection logic) (a) When the ECM directs the transmission to switch to 2nd gear, the actual gear is shifted to 1st. (b) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 3rd. (c) When the ECM directs the transmission to switch to 5th gear, the engine overruns (clutch slips). | ·Valve body is blocked up or stuck (1-2 shift valve)·Shift solenoid valve SLT remains open or closed·Automatic transmission (clutch, brake or gear, etc.) |
Monitor Strategy
| Related DTCs | P0781: Valve body/Functional check |
| Required sensors/Components | Valve body, Automatic transmission assembly |
| Frequency of operation | Continuous |
| Duration | Condition (A) and (B) 0.4 seconds Condition (C) 3 seconds Condition (D) 1 second |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
Typical Enabling conditions
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0979, P0980 (Shift solenoid valve S3 circuit) P0982, P0983 (Shift solenoid valve S4 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit) P0327, P0328, P032C, P032D (KCS sensor circuit) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | “D” |
| Duration time from shifting “N” to “D” | 4 seconds or more |
| ECT | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Output speed | 2nd → 1st down-shift point or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| Calculated load value | 7.75% or more (A/C off) 7.75% or more (A/C on) |
| Input speed/output speed (NT/NO) NT: Input (Turbine) speed NO: Internal counter shaft speed | 3.11 to 7.58 or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
| ECM selected gear | 4th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| Calculated load value | 7.75% or more (A/C off) 7.75% or more (A/C on) |
| Input speed/output speed (NT/NO) NT: Input (Turbine) speed NO: Internal counter shaft speed | 3.11 to 7.58 or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Vehicle speed (During transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 5th |
| Engine speed -Turbine speed (NE – NT) (After transition to 5th gear) | 150 rpm or less |
| Vehicle speed (After transition to 5th gear) | Less than 100 km/h (62.2 mph) |
Procedure
1. Check DTC output (In addition to DTC P0781)
a. Connect the Diagnostic scanners.
b. Read the DTCs.
| Result | Proceed to |
|---|---|
| Only P0781 is output | A |
| P0781 and other DTCs are output | B |
A>> Perform active test.
B>> Go to DTC chart.
2. Perform active test (running test)
Caution: This test should always be performed with at least 2 people.
a. Connect the diagnostic scanners.
b. Clear the DTC.
c. Warm up the engine.
d. According to the display on the diagnostic scanners, perform the active test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operate shift solenoid valve and set each shift position | ·Press “→” button: Shift up·Press “←” button: Shift down | Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (30 mph) or less |
Ok>> Perform active test (shift solenoid valve SLT)
NG>> Repair or replace transmission valve body assembly.
3. Perform active test using Diagnostic scanners (Shift solenoid valve SLT)
a. Remove the test plug on the transmission case center right side and connect SST.
b. Connect the diagnostic scanners.
c. Start the engine and warm it up.
d. Measure the line pressure with SST.
e. According to the display on the diagnostic scanners, perform the active test.
f. Measure the line pressure.

| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Solenoid (SLT)* | Operate shift solenoid SLT and raise line pressure | ON or OFF HINT:·OFF: Line pressure up (when Active Test “Activate the Solenoid (SLT)” is performed, ECM commands SLT solenoid to turn OFF)·ON: No action (normal operation) | [Vehicle Condition] ·Vehicle stopped·Engine idling |
OK>> Cleasr DTC and perform running test.
NG>> Replace shift solenoid valve SLT.
4. Clear DTC and perform running test.
a. Clear DTC.
b. Check for DTC again after conducting the monitor drive pattern.
OK>> No DTC output.
Ok>> END.
NG>> Repair or replace automatic transmission assembly.