Transmission Manuals – All data about Transmission

P0776  Pressure Control Solenoid “B” Performance (Shift Solenoid Valve SL2)

Description:
The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).

Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake, gear, etc.).

DTC CodeDTC Detection ConditionTrouble Area
P0766S4 stuck OFF malfunction or brake control valve malfunction*:Shifting to 5th and 6th gears is impossible.The ECM determines there is a malfunction when the following conditions are both met. (2-trip detection logic)
(a) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 4th.
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th.
·Shift solenoid valve S4 remains closed·Shift solenoid valve SLT remains open or closed·Valve body is blocked (Brake control valve)·Automatic transmission (clutch, brake or gear, etc.)
P0776SL2 stuck ON malfunction or brake control valve malfunction*:Shifting to 5th and 6th gears is impossible.The ECM determines there is a malfunction when the following conditions are both met. (2-trip detection logic)
(a) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 4th.
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th.
·Shift solenoid valve SL2 remains closed·Shift solenoid valve SLT remains open or closed·Valve body is blocked (Brake control valve)·Automatic transmission (clutch, brake or gear, etc.)

Monitor Strategy

Related DTCsP0766: Shift solenoid valve S4/Functional check
P0776: Shift solenoid valve SL2/Functional check
Required sensors/ComponentsShift solenoid valve S4, Speed sensor (NT), Speed sensor (SP2), Crankshaft position sensor (NE)
Frequency of operationContinuous
Duration0.4 seconds
MIL operation2 driving cycles
Sequence of operationNone

Typical Enabling Conditions

The monitor will run whenever the following DTCs are not presentP0717 (Turbine speed sensor circuit)
P0722 (Output speed sensor circuit)
P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit)
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0979, P0980 (Shift solenoid valve S3 circuit)
P0982, P0983 (Shift solenoid valve S4 circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit)
P0327, P0328, P032C, P032D (KCS sensor circuit)
ETCS (Electric Throttle Control System)Not system down
Transmission position“D”
Duration time from shifting “N” to “D”4 seconds or more
ECT40°C (104°F) or higher
Spark advance from max. retard timing by KCS control0° crankshaft angle or more
EngineStarting
Calculated load value7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.11 to 7.58
or
1.83 to 2.27
or
1.24 to 1.49
or
0.93 to 1.07
or
0.66 to 0.80
or
0.51 to 0.65
ECM selected gear5th
Vehicle speed2 km/h (1.2 mph) or more
Throttle valve opening angle9% or more at 2000 rpm
(Conditions vary with engine speed)
ECM selected gear6th
Vehicle speed2 km/h (1.2 mph) or more
Throttle valve opening angle9% or more at 2000 rpm
(Conditions vary with engine speed)

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]

Both of the following conditions are met: OFF malfunction (A) and (B)

Turbine speed/Output speed (NT/NO)0.93 or more, and 1.07 or less
(This means actual gear is 4th)
Turbine speed/Output speed (NT/NO)0.93 or more, and 1.07 or less
(This means actual gear is 4th)

[ON malfunction]

Both of the following conditions are met: ON malfunction (A) and (B)

Turbine speed/Output speed (NT/NO)0.93 or more, and 1.07 or less
(This means actual gear is 4th)
Turbine speed/Output speed (NT/NO)0.93 or more, and 1.07 or less
(This means actual gear is 4th)

Procedure
1. Check DTC output (in addtition to DTCS P0766 and P0776)
a. Connect the diagnostic tools.

ResultProceed to
Only P0766 and P0776 are outputA
P0766, P0776 and other DTCs are outputB

A>> Perform active test.
B>> Go to DTC chart.

2. Perform active test (shift solenoid value SLT)

a. Remove the test plug on the transmission case center right side and connect SST.

b. Start the engine and warm it up.

c. Measure the line pressure with SST.

d. According to the display on the diagnostictools, perform the active test.

e. Measure the line pressure.

Tester DisplayTest PartControl RangeDiagnostic Note
Activate the Solenoid (SLT)*Operate shift solenoid SLT and raise line pressureON or OFF
HINT:·OFF: Line pressure up (when Active Test “Activate the Solenoid (SLT)” is performed, ECM commands SLT solenoid to turn OFF)·ON: No action (normal operation)
[Vehicle Condition]
·Vehicle stopped·Engine idling

Ok>> Inspect shift solenoid valve s4.
NG>> Replace shift solenoid valve SLT.

3. Inspect shift solenoid valve S4

a. Remove shift solenoid valve S4.

b. Measure the resistance according to the value(s) in the table below.

Tester ConnectionConditionSpecified Condition
Shift solenoid valve S4 connector terminal – Shift solenoid valve S4 body20°C (68°F)11 to 15 Ω

c. Connect the battery’s positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. Then check that the valve moves and makes an operating noise.

OK:Valve moves and makes an operating noise.

OK>> Inspect shift solenoid valve SL2.
NG>> Repalce shift solenoid valve S4.

4. Inspect shift solenoid valve SL2.

a. Remove shift solenoid valve SL2.

b. Measure the resistance according to the value(s) in the table below.

Tester ConnectionConditionSpecified Condition
1 – 220°C (68°F)5.0 to 5.6 Ω

c. Connect the battery’s positive (+) lead with a 21 W bulb to terminal 1 and the negative (-) lead to terminal 2 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
OK: Valve moves and makes an operating noise.

OK>> Inspection transmission valve body assembly.
NG>> Replace shiftsolenoid valve SL2.

5. Inspect transmission valve body assembly.
a. Check the transmission valve body assembly.
OK: There are no foreign objects on any valve.
OK>> Repair or replace automatic transmission assembly.
NG>> Repair or repalce transmission valve body assembly.