P0756 Shift Solenoid “B” Performance (Shift Solenoid Valve S2)
Description:
The ECM uses signal from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the ECM compares the actual gear with the shift shcedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake, gear…).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0756 | S2 stuck ON malfunction*1:Shifting to 3rd and 5th gears is impossible.The ECM determines there is a malfunction when the following conditions are both met. (2-trip detection logic) (a) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 6th. (b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 6th. | ·Shift solenoid valve S2 remains closed·Valve body is blocked·Automatic transmission (clutch, brake, gear, etc.) |
| P0756 | S2 stuck OFF malfunction*2:The vehicle starts in 3rd gear and shifting to 6th gear is impossible.The ECM determines there is a malfunction when the following conditions are both met. (2-trip detection logic) (a) When the ECM directs the transmission to switch to 1st gear, the actual gear is shifted to 3rd. (b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 5th. | ·Shift solenoid valve S2 remains open·Shift solenoid valve SLT remains open or closed·Valve body is blocked·Automatic transmission (clutch, brake, gear, etc.) |
Monitor strategy:
| Related DTCs | P0756: Shift solenoid valve S2/Functional check |
| Required sensors/Components | Shift solenoid valve S2 |
| Frequency of operation | Continuous |
| Duration | 0.4 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
Typical Enabling Conditions:
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0979, P0980 (Shift solenoid valve S3 circuit) P0982, P0983 (Shift solenoid valve S4 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit) P0327, P0328, P032C, P032D (KCS sensor circuit) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | “D” |
| Duration time from shifting “N” to “D” | 4 seconds or more |
| ECT | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| Calculated load value | 7.75% or more (A/C off) 7.75% or more (A/C on) |
| Input speed/output speed (NT/NO) NT: Input (Turbine) speed NO: Internal counter shaft speed | 3.11 to 7.58 or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
| ECM selected gear | 1st |
| Vehicle speed | 2 km/h (1.2 mph) or more and less than 40 km/h (24.9 mph) |
| Engine speed – Turbine speed (NE – NT) | 50 rpm or more |
| ECM selected gear | 6th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 6th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
Procedure:
1. Check DTC output (in addition to DTC P0756)
a. Connet the diagnostic tools.
Result:
| Result | Proceed to |
|---|---|
| Only P0756 is output | A |
| P0756 and other DTCs are output | B |
3. Inspect shift solenoid valve S2.
a. Remove shift solenoid valve S2.
b. Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve S2 connector terminal – Shift solenoid valve S2 body | 20°C (68°F) | 11 |
c. Connect the battery’s positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. then check that the valve moves and makes an operating noise.

OK>> Inspect transmission valve body assmbly.
NG>> Replace shift solenoid valve S2.
4. Inspect transmission valve body assembly.
a. Check the transmission valve body assembly.
OK>> There are no foreign objects on any valve.
OK>> Repair or replace automatic transmission assembly.
NG>> Repair or replace transmission valve body assembly.