P0751 Shift Solenoid “A” Performance (Shift Solenoid Valve S1)
Description:
The ECM uses signal from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the ECM compares the actual gear with the shift shcedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake, gear…).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0751 | S1 stuck ON malfunction*1:The ECM determines there is a malfunction when the following conditions are both met. (2-trip detection logic) (a) When the ECM directs the transmission to switch to 1st gear, the actual gear is shifted to 2nd. (b) When the ECM directs the transmission to switch to 5th gear, the actual gear is also shifted to 5th. | ·Shift solenoid valve S1 remains closed·Valve body is blocked·Automatic transmission (clutch, brake or gear, etc.) |
| P0751 | S1 stuck OFF malfunction*2:The ECM determines there is a malfunction when conditions (a) and (b) are met. (2-trip detection logic) (a) When the ECM directs the transmission to switch to 5th gear, the actual gear is also shifted to 5th. (b) When the ECM directs the transmission to switch to 6th gear, the engine overruns (clutch slips). | ·Shift solenoid valve S1 remains open·Shift solenoid valve SLT remains open or closed·Valve body is blocked·No. 2 brake malfunction (Driving is difficult.)·Automatic transmission (clutch, brake or gear, etc.) |
Monitor strategy:
| Related DTCs | P0751: Shift solenoid valve S1/Functional check |
| Required sensors/Components | Shift solenoid valve S1, Speed sensor (NT), Speed sensor (SP2), Crankshaft position sensor (NE), Throttle position sensor, MAF |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) and ON malfunction (A), (B) 0.4 seconds OFF malfunction (B) 3 seconds OFF malfunction (C) 1 second |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
Typical Enabling Conditions:
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0979, P0980 (Shift solenoid valve S3 circuit) P0982, P0983 (Shift solenoid valve S4 circuit) P0985, P0986 (Shift solenoid valve SR circuit) P0748 (Shift solenoid valve SL1 circuit) P0778 (Shift solenoid valve SL2 circuit) P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit) P0327, P0328, P032C, P032D (KCS sensor circuit) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | “D” |
| Duration time from shifting “N” to “D” | 4 seconds or more |
| ECT | 40°C (104°F) or higher |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| Calculated load value | 7.75% or more (A/C off) 7.75% or more (A/C on) |
| Input speed/output speed (NT/NO) NT: Input (Turbine) speed NO: Internal counter shaft speed | 3.11 to 7.58 or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
| Current ECM selected gear | 6th |
| Last ECM selected gear | 5th |
| Vehicle speed (During transition from 5th to 6th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 6th |
| Engine speed-Turbine speed (NE-NT) (After transition from 5th to 6th gear) | 150 rpm or less |
| Vehicle speed (After transition from 5th to 6th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 1st |
| Vehicle speed | 2 km/h (1.2 mph) or more and less than 40 km/h (24.9 mph) |
| Engine speed-Turbine speed (NE-NT) | 50 rpm or more |
| Calculated load value | 7.75% or more (A/C off) 7.75% or more (A/C on) |
| Input speed/output speed (NT/NO) NT: Input (Turbine) speed NO: Internal counter shaft speed | 3.11 to 7.58 or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| Calculated load value | 7.75% or more (A/C off) 7.75% or more (A/C on) |
| Input speed/output speed (NT/NO) NT: Input (Turbine) speed NO: Internal counter shaft speed | 3.11 to 7.58 or 1.83 to 2.27 or 1.24 to 1.49 or 0.93 to 1.07 or 0.66 to 0.80 or 0.51 to 0.65 |
Procedure:
1. Check DTC output (in addition to DTC P0751)
a. Connet the diagnostic tools.
Result:
| Result | Proceed to |
|---|---|
| Only P0751 is output | A |
| P0751 and other DTCs are output | B |
2. Perform active test using diagnostic tools (Shift solenoid valve SLT)
a. Remove the test plug on the transmission case center right side and connect SST.
b. Connect diagnostic tools.
c. Start the engine and warm it up.
d. Measure the line pressure with SST.
e. According to the display on the diagnostic tools, perform the active test.
f. Measure the line pressure.

| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Solenoid (SLT)* | Operate shift solenoid SLT and raise line pressure | ON or OFF HINT:·OFF: Line pressure up (when Active Test “Activate the Solenoid (SLT)” is performed, ECM commands SLT solenoid to turn OFF)·ON: No action (normal operation) | [Vehicle Condition] ·Vehicle stopped·Engine idling |
3. Inspect shift solenoid valve S1.
a. Remove shift solenoid valve S1.
b. Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve S1 connector terminal – Shift solenoid valve S1 body | 20°C (68°F) | 11 to 15 Ω |
c. Connect the battery’s positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid valve body. then check that the valve moves and makes an operating noise.

OK>> Inspect transmission valve body assmbly.
NG>> Replace shift solenoid valve S1.
4. Inspect transmission valve body assembly.
a. Check the transmission valve body assembly.
OK>> There are no foreign objects on any valve.
OK>> Repair or replace automatic transmission assembly.
NG>> Repair or replace transmission valve body assembly.