P0748 Pressure Control Solenoid “A” Electrical (Shift Solenoid Valve SL1)
Description:
Shifting from 1st to 5th is performed is combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled the ECM. If an open or short circuit occurs in the shift solenoid valves, the ECM controls the remianing normal shift solenoid valves to allow the vehicle to be operation safely.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0748 | The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gear (1 trip detection logic) Output signal duty equals to 100% HINT:SL1 output signal duty is less than 100% under normal condition | ·Open or short in shift solenoid valve SL1 circuit·Shift solenoid valve SL1·ECM |
Monitor Strategy:
| Related DTCs | P0748: Shift solenoid valve SL1/Range check |
| Required sensors/Components | Shift solenoid valve SL1 |
| Frequency of operation | Continuous |
| Duration | 1 second |
| MIL operation | Immediately |
| Sequence of operation | None |
Typical Enabling Conditions:
| The monitor will run whenever the following DTCs are not present | None |
| Ignition switch | ON |
| Starter | OFF |
| Solenoid current cut status | Not cut |
| Battery voltage | 11 V or more |
Wiring diagram:

Hint:
the shift solenoid valve SL1 turns ON/OFF normally when the shift lever is on D:
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve SL1 | OFF | OFF | OFF | OFF | ON | ON |
Procedure:
1. Inspect No. 1 transmission wire (shift solenoid valve SL1)
a. Disconnect the D63 No. 1 transmisson wire connector.
b. Measure the resistance according to the value(s) in the table blow:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 11 (SL1+) – 3 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| 11 (SL1+) – Body ground | Always | 10 kΩ or higher |
| 3 (SL1-) – Body ground | Always | 10 kΩ or higher |

OK>> Check harness and connector (No. 1 transmission wire ECM)
NG>> Inspect shift solenoid valve SL1.
2. Check harness and connector (No.1 transmission wire – ECM).
a. Disconnect the D74 ECM connector.
b. Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D74-14 (SL1+) – D74-15 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| D74-14 (SL1+) – Body ground | Always | 10 kΩ or higher |
| D74-15 (SL1-) – Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |

A>> Repair or replace harness or connector.
B>> Replace ECM.
3. Inspect shift solenoid valve SL1.
a. Remove shift solenoid valve SL1.
b. Measure the reisistance according to the valvue(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 – 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
c. Connect the battery’s positive (+) lead with a 21 W bulb to terminal 1 and the negative (2) lead to terminal 2 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
OK: Valve moves and makes an operating noise.

OK>> Repair or replace No. 1 transmission wire.
NG>> Replace shift solenoid valve SL1.