Transmission Manuals – All data about Transmission

P0729  Gear 6 Incorrect Ratio 

Description:
The ECM uses signals from the output speed sensor SP2 and input speed sensor NT to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear). Then the ECM compares the actual gear with the shift shedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve bodt or automatic transmissin (clutch, brake, gear, etc.).

DTC CodeDTC Detection ConditionTrouble Area
P07296th gearshift malfunction:The ECM determines there is a malfunction when both of the following conditions are met. (2-trip detection logic)
(a) When the ECM directs the transmission to switch to 5th gear, the actual gear is also shifted to 5th.
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th.
·Valve body is blocked up or stuck (sequence valve)·Shift solenoid valve SLT remains open or closed·Automatic transmission (clutch, brake or gear, etc.)

Typical enabling conditions:

The monitor will run whenever the following DTCs are not presentP0717 (Turbine speed sensor circuit)
P0722 (Output speed sensor circuit)
P0710, P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor circuit)
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0979, P0980 (Shift solenoid valve S3 circuit)
P0982, P0983 (Shift solenoid valve S4 circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine coolant temperature) sensor circuit)
P0327, P0328, P032C, P032D (KCS sensor circuit)
ETCS (Electric Throttle Control System)Not system down
Transmission position“D”
Duration time from shifting “N” to “D”4 seconds or more
ECT40°C (104°F) or higher
Spark advance from max. retard timing by KCS control0° crankshaft angle or more
EngineStarting
Calculated load value7.75% or more (A/C off)
7.75% or more (A/C on)
Input speed/output speed (NT/NO)
NT: Input (Turbine) speed
NO: Internal counter shaft speed
3.11 to 7.58
or
1.83 to 2.27
or
1.24 to 1.49
or
0.93 to 1.07
or
0.66 to 0.80
or
0.51 to 0.65

Procedure:
1. Check DTC output (in addition to DTC P0729)

ResultProceed to
Only P0729 is outputA
P0729 and other DTCs are outputB

2. Perform active test (running test).

This test should alwys be performed with at least 2 people.

– Perform the test at the normal operating ATF temprature: 50 to 80 degree C (122 to 176 degree F).
Perform the test with the A/C turned off.

Engine and ECT:

Tester DisplayTest PartControl RangeDiagnostic Note
Control the Shift PositionOperate shift solenoid valve and set each shift position·Press “→” button: Shift up·Press “←” button: Shift downPossible to check operation of shift solenoid valves
[Vehicle Condition]
50 km/h (30 mph) or less

3. Perform active test (shift solenoid valve SLT).
– Perform the test at the normal operating ATF temperature: 50 to 80 degree C (122 to 176 degree F).
– Be cafeful to prevent SST’s hose from interfering with the exhaust pipe.
– Perform the test with the A/C off.

a. Remove the test plug on the transmission case center right side and connect SST.

b. Connect the diagnostic scanner.

c. Start the engine and warm it up.

d. Measure the line pressure with SST.

e. Turn on the diagnostic scanner.

f. According to the display on the diagnostic, perform the active test.

g. Measure the line pressure.

Engine and ECT:

Tester DisplayTest PartControl RangeDiagnostic Note
Activate the Solenoid (SLT)*Operate shift solenoid SLT and raise line pressureON or OFF
HINT:·OFF: Line pressure up (when Active Test “Activate the Solenoid (SLT)” is performed, ECM commands SLT solenoid to turn OFF)·ON: No action (normal operation)
[Vehicle Condition]
·Vehicle stopped·Engine idling

Ok>> Clear DTC and perform running test.
NG>> Replace shift solenoid valve SLT.

5. Clear DTC and perform running test.
OK>> end.
NG>> Repair or replace automatic transmission assembly.