P0717 Turbine Speed Sensor Circuit No Signal
Descriotion:
This sensor detects the rotation speed of the turbine which shows the input revolution of the transmission. By comparing the input turbine speed signal NT with the counter gear speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions and as a result, the gears shift smoothly.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0717 | All conditions below are detected for 5 seconds or more (1-trip detection logic) (a) Gear change is not performed (b) Gear position: 4th, 5th or 6th (c) T/M input shaft rpm: Less than 300 rpm (d) T/M output shaft rpm: 1000 rpm or more (e) Park/neutral position switch: ·NSW input signal is OFF·R input signal is OFF (f) Shift solenoid valves and park/neutral position switch are operating normally | ·Open or short in speed sensor NT circuit·Speed sensor NT·ECM·Automatic transmission (clutch, brake or gear, etc.) |
Typical enabling conditions:
| The monitor will run whenever the following DTCs are not present | P0705 (Park/neutral position switch circuit) P0751, P0973, P0974 (Shift solenoid valve S1) P0756, P0976, P0977 (Shift solenoid valve S2) P0761, P0979, P0980 (Shift solenoid valve S3) P0766, P0982, P0983 (Shift solenoid valve S4) P0748 (Shift solenoid valve SL1 circuit) P0776, P0778 (Shift solenoid valve SL2) |
| Shift change | After shift change is completed and before starting next shift change operation |
| ECM selected gear | 4th, 5th or 6th |
| Output shaft rpm | 1000 rpm or more |
| NSW switch | OFF |
| R switch | OFF |
| Engine | Running |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
Wiring diagram P0717:

Data list:
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| SPD (NT) | Input shaft speed/ Min.: 0 rpm Max.: 12750 rpm | Lock-up is: ·ON (after warming up engine): Input turbine speed (NT) is equal to engine speed·OFF (idling with shift lever on N): Input turbine speed (NT) is nearly equal to engine speed | Data is displayed in increments of 50 rpm |
Procedure:
1. Inspect speed sensor NT installation
Check the speed sensor NT installation? OK >> The isntallation bolt is tightened is no clearance between the sensor and transmission case.

2. Inspect speed sensor NT.
a. Disconnect the D65 speed sensor connector.
b. Measure the resistance according to the value(S) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 – 2 | 20°C (68°F) | 560 to 680 Ω |

3. Check harness and connector (speed sensor NT – ECM)
a. Disconnect the D47 ECM connector.
b. Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D74-124 (NT+) – D74-123 (NT-) | 20°C (68°F) | 560 to 680 Ω |
| D74-124 (NT+) – Body ground | Always | 10 kΩ or higher |
| D74-123 (NT-) – Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
NG: Repair or replace harness of connector.
OK: Replace ECM.
